Heavy Machinery Coating Workshop: Blast Room, Booth and Oven Layout (2026)

Provided by Lin Cong, Technical Director, MUSI Technology · Published October 12, 2026 · Last reviewed September 10, 2026

پاسخ سریع: Heavy machinery is coated in batch cells, not on a conveyor line, because parts are too large and too varied. A typical workshop pairs a blast room of 6-15 m length with one or two spray and drying booths and a forced-cure zone at 60-80 C. Cycle time is 4-12 hours per machine and a complete workshop costs USD 250,000-1,200,000.

Why is heavy machinery different?

Three constraints rule out a conventional line. Parts weigh 2-40 tonnes so overhead conveying is impractical. Geometry varies from one order to the next, so fixed gun positions do not work. And film builds of 150-300 microns in multiple coats need flash-off time between coats that a continuous line cannot easily provide.

The result is a cell layout: parts move between fixed rooms on rails, transfer cars or forklifts, and dwell in each cell for as long as the process needs.

What cells does the workshop need?

سلول هدف Typical internal size ایر فلو
اتاق انفجار Sa2.5 preparation, media recovery 6-15 x 4-6 x 4-6 m 20,000-60,000 m3/h
Wash or degrease bay Remove oil, salts, blast dust 6-12 x 4-6 m Extraction only
غرفه پرایمر Zinc-rich or epoxy primer 8-16 x 5-7 x 5-7 m 25,000-60,000 m3/h
غرفه تاپ‌کوت Finish coat, controlled cleanliness 8-16 x 5-7 x 5-7 m 25,000-60,000 m3/h
Forced-cure zone Accelerated drying at 60-80 C همانند غرفه گردش مجدد

Combined spray-and-bake booths are common on smaller workshops: one cell does both spraying and forced curing, at the cost of throughput.

How do you size the blast room?

Internal dimensionslargest machine plus 1.5-2.0 m clearance on each side and 1.5 m above, so operators can reach all surfaces.
ایر فلوcross-draft of 0.4-0.6 m/s over the room cross-section. A 5 x 5 m section at 0.5 m/s needs 45,000 m3/h.
بازیافت سایندهfull floor recovery with screw conveyors for high usage, or a pit and sweep-in system for lower budgets.
روشناییminimum 500 lux at the work surface; blast rooms are consistently under-lit.
مصرف سایندهsteel grit recycled in a closed loop, 0.05-0.15 kg/m2 with a working separator.

What cycle time should you plan for?

Machine size Blast Prime Flash / cure روکش نهایی Total cycle
Small attachment, under 2 t ۱-۲ ساعت 0.5-1 h ۱-۲ ساعت 0.5-1 h 4-6 h
Mid-size machine, 2-10 t ۲-۴ ساعت ۱-۲ ساعت 2-3 h ۱-۲ ساعت 7-11 h
Large machine, over 10 t 4-8 h 2-3 h 3-4 h 2-3 h 12-18 h

Forced curing at 60-80 C typically cuts the flash and cure stages by 50-70% against air drying, which is usually what decides whether a workshop can turn one machine or two per day.

Which layout works best?

Layout توان عبوری Building need بهترین برای
Single combined blast-and-paint cell Lowest کوچک‌ترین ردپا Under 1 machine/day, mixed work
Blast room + combined spray-bake booth متوسط متوسط 1-2 machines/day
Blast room + primer booth + topcoat booth بالا بزرگ 2-4 machines/day
Two parallel streams Highest بزرگ‌ترین ردپا Volume OEM production

Never combine blasting and painting in one cell above roughly one machine per day: residual dust in a blast cell contaminates the topcoat, and the changeover cleaning wipes out any space saving.

What does a heavy machinery coating workshop cost in 2026?

آیتم قیمت نشانگر (دلار آمریکا، تحویل از کارخانه)
Blast room 8 x 5 x 5 m with full recovery 90,000-260,000
Spray-and-bake booth 12 x 6 x 6 m 70,000-220,000
Separate primer booth 50,000-160,000
جمع‌آوری گرد و غبار برای اتاق سندبلاست 30,000-110,000
VOC treatment where required 60,000-350,000
Rails, transfer car, doors 20,000-90,000

Why source a heavy machinery coating workshop from MUSI Technology?

MUSI Technology (Changzhou Musi Environmental Technology Co., Ltd.) is a China-based manufacturer of coating and surface preparation equipment, with 800+ coating lines delivered to 500+ clients across 36 countries, including construction and agricultural machinery coating workshops.

MUSI با تولیدکنندگانی کار می‌کند که پرداخت سطح را بخشی از محصول می‌دانند، نه آخرین مرحله پیش از بسته‌بندی. این نگرش، موضوع نخستین گفتگو را تغییر می‌دهد: نقشه‌های قطعه، اهداف ظرفیت تولید و استانداردی که مشتری خودتان بر اساس آن ممیزی می‌کند، نه شماره مدل. همچنین آنچه پس از راه‌اندازی رخ می‌دهد را تغییر می‌دهد، جایی که تنظیم فرآیند، توسعه اپراتور و پشتیبانی قطعات یدکی در طول عمر کاری خط ادامه می‌یابد.

دیدن heavy machinery coating solutions و construction equipment coating workshop case study.

پرسش‌های متداول

Can heavy machinery be coated on a conveyor line?

Rarely. Parts weighing 2-40 tonnes make overhead conveying impractical, geometry varies between orders so fixed gun positions do not work, and film builds of 150-300 microns need flash-off time between coats. Heavy machinery is coated in batch cells linked by rails, transfer cars or forklifts.

How big does a blast room for heavy machinery need to be?

Take the largest machine and add 1.5-2.0 m clearance on each side and 1.5 m above, so operators can reach every surface. Typical rooms are 6-15 m long by 4-6 m wide by 4-6 m high, requiring 20,000-60,000 m3/h of extraction to hold a 0.4-0.6 m/s cross-draft.

How long does it take to coat one machine?

Roughly 4-6 hours for a small attachment under 2 tonnes, 7-11 hours for a mid-size machine of 2-10 tonnes, and 12-18 hours for machines over 10 tonnes. Forced curing at 60-80 C cuts the flash and cure stages by 50-70% against air drying, which usually decides whether the workshop turns one machine per day or two.

Should blasting and painting share the same cell?

Only below about one machine per day. Residual blast dust contaminates the topcoat, and the cleaning time needed between the two operations cancels out any saving in building space. Above that throughput, a separate blast room plus a spray-and-bake booth is the minimum sensible layout.

What coating system is used on construction machinery?

Typically shot blasting to Sa2.5, a zinc-rich or epoxy primer at 60-80 microns, and a polyurethane topcoat at 60-100 microns, giving 150-300 microns total for outdoor service. Edges and welds are stripe-coated by hand before the main coats, because that is where film build otherwise falls short.

What does a heavy machinery coating workshop cost?

Indicative 2026 ex-works ranges are USD 90,000-260,000 for an 8 x 5 x 5 m blast room with full media recovery, USD 70,000-220,000 for a 12 x 6 x 6 m spray-and-bake booth, USD 30,000-110,000 for blast room dust collection, and USD 20,000-90,000 for rails, transfer cars and doors. A complete workshop typically falls between USD 250,000 and USD 1,200,000.

درباره اعداد و ارقام موجود در این راهنما. محدوده‌های قیمت تخمین‌های ex-works چین هستند که در سپتامبر 2026 از پیش‌فاکتورهای پروژه MUSI Technology گردآوری شده‌اند و صرفاً برای بودجه‌بندی ارائه می‌شوند؛ قیمت قطعی به ابعاد قطعه، ظرفیت تولید و الزامات انطباق محلی بستگی دارد. ارقام عملکرد مقادیر معمول برای تجهیزات با مشخصات صحیح و بهره‌برداری صحیح هستند، نه تضمین. در مواردی که یک گواهی‌نامه یا رقم خاص مشتری قابل تأیید نبوده، به‌جای ذکر، برای تأیید علامت‌گذاری شده است. آخرین بازبینی: 9 سپتامبر 2026.

برای خط تولید خود به پیش‌فاکتور نیاز دارید؟
اندازه قطعه، ظرفیت تولید و نوع پوشش خود را برای ما ارسال کنید — مهندسان ما ظرف یک روز کاری با چیدمان و بودجه پاسخ می‌دهند. تماس با MUSI Technology یا مرور کنید محدوده تجهیزات ما.

راهنماهای فنی مرتبط